力士樂伺服驅動器維修圖解：上海仰光電子科技有限公司專業從事各品牌伺服驅動器維修,伺服電機維修,觸摸屏維修,變頻器維修,伺服器維修,伺服控制器維修,數控系統維修改造，機器人維修保養以及各種板卡,芯片級維修維護,免費檢測,快速維修,部分立等可取!
博世力士樂伺服驅動器維修檢測：
F644 Negative Travel Limit Switch Detected
檢測到負行程限位開關
The negative travel limit switch has been actuated. The axis has been
stopped with the error reaction "set velocity command value to zero". Bit 2
of P-0-0090, Travel limit parameter has been set to "Exceeding the
travel limit is considered as an error", or a drive control command has
been started while the axis limit value is exceeded (e.g. drive-controlled
homing).
負行程限位開關已啟動。軸已經以錯誤反應“將速度命令值設置為零”停止。第2位P-00090中，行程限制參數已設置為“超過行程限制被視為錯誤”，或驅動控制命令已在超過軸極限值時啟動（例如，驅動控制歸位）。
Cause:原因：
The negative travel limit switch has been actuated
負行程限位開關已啟動
Remedial action:補救措施：
1. Reset the error
重置錯誤
2. Activate the power supply
激活電源
3. Move the axis into the permissible working range
將軸移動到允許的工作范圍內
Note: The drive will not accept any command values that lead further away from the permissible range. Specifying such a command will again result in this error.注意：驅動器不會接受任何遠離允許范圍的命令值。指定這樣的命令將再次導致此錯誤。
轉載請注明出處：上海仰光電子科技專業伺服驅動器維修,伺服電機維修
本文鏈接：http://www.jyluyida.com/fuwu/Services_Show26634.htm
伺服驅動器維修 伺服電機維修 觸摸屏維修 變頻器維修
電話：021-50157782
手機：13817011982 微信同號
郵箱：shygdzi@163.com
聯系人：張工
網址：http://www.jyluyida.com
【 我們確保修好測試好給客戶�。。�！】
下一篇：沒有了
